Solid wood flooring paint white reason

1097 views 4 replies

xiao1236

Age: 2023
Total Posts: 7017
Points: 10

Location:
,

Wood flooring paint whitening refers to the coating process and just finished coating surface was milky white. The coating film is not only white, but also white like a cloud of whitening phenomenon. Whitish This situation occurs in high-humidity environment, spraying volatile coatings occasions, severe complete loss of light, the coating appears microporous, is due to rapid evaporation of solvent within the paint, so that Tu surface temperature decreases, resulting in atmospheric moisture In the paint surface condensation, sinking into the coating and lead to resin precipitation and white. Solid wood flooring paint surface whitening reasons: 1, the construction environment humidity is too large, the floor coating process is too thick, the diluent used poor quality and other reasons, because the summer high temperatures, air humidity in some areas. Drying time of the paint layer with the temperature increased, but the hard work time is relatively slow, 2, the painter in the floor construction process, may ignore the hard work time, and in the paint layer dry, immediately on the other A paint. Resulting in the bottom of the paint is not completely dry. In rainy days or high humidity weather, prone to paint the phenomenon of white. 3, the temperature of the floor spraying cold, especially when the temperature of the coating is below room temperature; spray indoor air circulation is poor, but also the lack of heating equipment. Solid wood flooring paint surface whitening solution: 1, in the summer use of wood floor paint decoration process, to focus on grasping the thickness of the film during the construction process, it is recommended thin coated several times. 2, to master the construction of the intermittent time, must be in the paint layer of hard work, and then proceed to the next process construction. To ensure the quality of wood construction. 3, wood and to be painted surface temperature to be consistent, not in the cold wood painting. Water-based paint can be applied in the sun and dry, but to avoid painting on hot surfaces. Solid wood flooring paint surface whitening Note: 1, the spraying place appropriate heating, increase the dryness, improve the ambient temperature. 2, the use of good quality, volatile slower diluent. 3, at the same time we should pay attention to the construction conditions are: temperature 10 ~ 30 ?; relative humidity 50% ~ 80% (the best condition is about 23 ?, modest not more than 70%), too high or too low temperature and humidity may lead to Tu Loaded effect.Related links: outdoor bistro table and stools metal clothes drying rack folding bed for military

Posted 17 Nov 2016

wangyueyue says

wangyueyue

Age: 32
2933 days old here
Total Posts: 18
Points: 10

Location:
shanghai, China

Stainless steel maintenance procedures stainless steel cleaning steps I believe we will have some of the number of stainless steel jewelry or appliances. In the
course of long-term use are likely to be more or less dirty. Many people wash
stainless steel methods are mostly brushed with steel ball violence, so there
may be "brand-new as" the illusion, in fact, so the damage to stainless steel
products is very large. This article describes the repair and cleaning of
stainless steel.Stainless steel wire suppliers As with other materials exposed to the atmosphere, stainless steel is also dirty. Future lectures will analyze design factors that impact
maintenance and clean-up costs. However, there is a correlation between rain
erosion, manual flushing, and dirty surfaces.high quality cold aluminum sheet rolling mill roll The effect of rain erosion was determined by placing the same slab directly in the atmosphere and in a shed. The effect of
manual flushing was determined by manually scrubbing the right side of each
panel with soapy water sponge every six months. As a result, it was found that
dust and silt removal by rain washing and manual scrubbing had a favorable
effect on the surface condition as compared with a slat placed in a shed and a
place not washed. But also found that the status of surface processing has an
impact on the smooth surface of the slab than the rough surface of the slab
effect is better.stainless steel L angle bar for wall covering So the scrubbing interval by a variety of factors, the main influencing factor is the required aesthetic standards.
Although many stainless steel curtain walls only in the Cabo rinse, but, in
general, for external stainless steel scrub twice a year.1 4 Wire Rope Galvanized

Posted 18 Nov 2016

loemrntdherid1 says

loemrntdherid1

Age: 2023
3107 days old here
Total Posts: 32
Points: 10

Location:
,